Post by MADMIKE on Jan 12, 2007 18:09:59 GMT -5
Models 20,
30, 50, 70
and 110
Instruction Manual
See inside for Quick Start Guide!
English
IMPORTANT SAFEGUARDS
WARNING–To guard against injury, basic safety precautions should be
observed, including the following:
1. For the complete enjoyment, use and understanding of this product,
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
and all-important notices on the AquaClear Power Filter before
using. Failure to do so may result in damage to the unit.
2. DANGER—To avoid possible electrical shock, special care should
be taken since water is employed in the use of this equipment. For
each of the following situations, do not attempt repairs yourself;
return the AquaClear Power Filter to an authorized service facility for
service or discard the appliance.
I. If the AquaClear Motor Unit falls into the water DO NOT reach
for it! First unplug it and then retrieve it. If any of the electrical
components of the AquaClear Power Filter gets wet, unplug
it immediately.
II. If the AquaClear Motor Unit shows any sign of abnormal water
leakage or if RCD (or GFCI- Ground Fault Current Interrupter)
switches off disconnect the power supply cord from mains and
remove pump from water.
III. Carefully examine the AquaClear Power Filter after installation. It
should not be plugged in if there is water on parts not intended to
be wet.
IV. Do not operate any appliance if it has a damaged cord or plug, or
if it is malfunctioning or if it is dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the
cord is damaged, the appliance should be discarded. Never cut
the cord.
V. To avoid the possibility of the AquaClear Power
Filter’s plug or receptacle getting wet, position the
unit to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug.
A “drip loop” (A) should be arranged to the receptacle. The “drip loop” is the part of the cord below the
level of the receptacle or the connector if an extension cord is used, to prevent water traveling along
the cord and coming into contact with the receptacle.
If the plug or receptacle does get wet, DO NOT
unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug
and examine for presence of water in the receptacle. A
3. Close supervision is necessary when any appliance is used by or
near children.
4. To avoid injury, do not contact moving parts or hot parts such
as heaters, reflectors, lamp bulbs, etc.
5. CAUTION— Always unplug or disconnect all appliances in the
aquarium from electricity supply before placing hands in water,
before putting on or taking off parts and whilst the equipment is
being installed, maintained or handled. When inserting or removing
the pump from the water, always pull out the main electricity plug.
Never yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect. Always unplug an appliance from an outlet when not
in use.
6. Do not use this pump for other than intended use (i.e.: do not use
in swimming pools, bathrooms, etc.). The use of attachments not
recommended or sold by the appliance manufacturer may cause an
unsafe condition.
· Do not use this pump in swimming pools or other situations where
people are immersed.
· This pump is suitable for use in water temperatures up to 35 °C.
· Do not use this pump with inflammable or drinkable liquids.
7. This pump is suitable for INDOOR use only. Do not install or store
the appliance where it will be exposed to the weather or to
temperatures below freezing.
8. Make sure an appliance mounted on a tank is securely installed
before operating it.
9. Read and observe all the important notices on the appliance.
10. If an extension cord is necessary, a cord with a proper rating
should be used. A cord rated for less amperes or watts than the
appliance rating may overheat. Care should be taken to arrange
the cord so that it will not be tripped over or pulled.The connection
should be carried out by a qualified electrical installer.
11. The pump must not run dry.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this power filter it is recommended that this manual is thoroughly read and understood.
Failure to do so may result in damage to this filter.
AQUACLEAR POWER FILTERS FLOW RATES
MODEL # 20 30 50 70 110
Maximum Flo Rate 100 gph 150 gph 200 gph 300 gph 500 gph
378 lph 568 lph 757 lph 1135 lph 1890 lph
Minimum Flo Rate 33 gph 50 gph 66.6 gph 100 gph 166.6 gph
125 lph 190 lph 250 lph 380 lph 630 lph
Watts 6 Watts 6 Watts 6 Watts 6 Watts 14 Watts
RPM 3600 rpm 3600 rpm 3600 rpm 3600 rpm 3600 rpm
POWER FILTER MAINTENANCE
Always unplug power filter prior to cleaning. Remove cover, filter basket, and discard water
remaining in the filter case. Thoroughly rinse collected debris from the case, impeller cover and
impeller assembly in clear lukewarm water. The intake “U” tube and extension tube can be
cleaned with a filter stem brush to remove any buildup of deposits. When all parts have been
cleaned and thoroughly rinsed, reassemble filter and replace onto aquarium.
(See Quick Start Guide 2, 3 and 4.)
Follow operating instructions to restart and prime power filter.
(See Power Filter Start-up.)
Every three months the
motor should be thoroughly
cleaned. Remove
cover, filter basket and
discard water remaining
in filter case. Remove
motor by twisting a 1/4
–turn gently in the direction
of the arrow on front.
Ease motor down slowly
to prevent damage to the
filter and motor guide.
Pull impeller out of
impeller well and rinse to
remove accumulated
slime deposits.
A cotton swab or
impeller well brush (not
supplied) can be used to
remove more stubborn
deposits. Wet motor seal
ring to prevent damage
before placing into filter
case.
HOW IT WORKS
The AquaClear Power Filter draws water from the aquarium
through an extension tube into the motor which then pumps water
out of the impeller assembly. The intake “U” tube directs the flow of
unfiltered water through filter inserts to trap particles, debris, and
purify the water.
CYCLEGUARD® MULTI-STAGE
FILTRATION SYSTEM
Provides optimal Mechanical, Chemical,
and Biological filtration
A healthy aquarium requires “beneficial” bacteria.
Invisible and harmless, beneficial bacteria are essential in the removal of
toxic ammonia and nitrite.
With cartridge filtration systems, when you throw away the cartridge, you throw away beneficial
bacteria. It can take weeks for the bacteria to recolonize, resulting in a stressful environment.
The AquaClear® multi-stage filtration system is different. Only one of three filtration components
is changed at a time. This ensures that significant amounts of beneficial bacteria remain. There
is never a sudden depletion of bacteria so biological filtration remains at highly effective levels.
Stage 1: Mechanical—Foam Filter Insert
AquaClear Foam Filter Inserts perform mechanical filtration by trapping particles and debris as
they pass through the insert. This unique foam, designed for use with AquaClear Power Filters,
features optimal pore size for efficient mechanical and biological filtration.
Stage 2: Chemical—Activated Carbon insert
AquaClear Activated Carbon Filter Insert contains 100% premium
research grade carbon. Premium research grade carbon provides
large amounts of surface area for adsorption of undesirable
impurities. The activated carbon filter insert will remove unwanted
odors, discoloration and impurities resulting in a crystal clear
aquarium.
Stage 3: Biological—BioMax Insert
AquaClear BioMax Filter Insert contains BioMax ceramic rings.
The surface of BioMax is made up of a complex pore system that
allows bacteria to thrive. Each ceramic ring contains approximately
100 square feet of surface area providing more biological power
than a traditional cartridge. Use of the BioMax Insert will provide optimal living space for beneficial
bacteria and enhance the removal of ammonia and nitrites resulting in a healthy aquarium
environment.
NOTE: Regular replacement of AquaClear filter inserts is essential for optimum
filter performance.
PATENTED REFILTRATION SYSTEM
For a healthy aquarium and clear water
Sometimes delicate fish and plants require a gentler water flow. AquaClear’s patented refiltration
system allows you to control the flow rate without compromising filtration efficiency.
When the flow rate is reduced, up to 50% of the water within the filter chamber is processed
multiple times. More impurities are filtered out, creating a healthier tank with sparkling clean
and clear water.
NOTE: A reduced flow rate is also recommended for use during feeding, to ensure more
efficient food consumption and less waste.
STAGE 1
STAGE 2
STAGE 3
®
Congratulations on the purchase of your new AquaClear
Power Filter. Please allow approximately 15-20 minutes
for the complete installation of filter parts and inserts.
The rewards to your aquatic adventures will be worth it!
Inspect AquaClear power filter for any visible signs of
shipping damage and verify that motor is securely fastened
to filter case. The following parts should be included
in your package.
*All AquaClear Power Filters, except Model 20, are shipped with two
extension tubes.
AquaClear® Power Filter Quick Start Guide
Filter
Case
Filter
Basket
Filter Cover
Intake
“U” Tube
Extension
Tube*
Motor
Leveling
Device
Foam
Carbon
Locking Clip
BioMax
Mesh Bag
. PACKING LIST
AquaClear Foam: Rinse foam insert and place into filter basket first. The foam block should
totally fill the bottom of the basket leaving no space between the filter basket base and sides.
Replace foam insert every two months.
AquaClear Carbon: Remove carbon insert from dust sleeve and rinse pouch to remove any
carbon dust particles. Flatten carbon insert and place horizontally on top of foam insert.
Replace carbon insert every month.
AquaClear BioMax: Open poly bag and transfer
contents into mesh bag. Apply locking clip
as shown, trim excess mesh, and thoroughly
rinse insert materials before placing on third
level of the basket.
Replace BioMax insert every three months.
NOTE: Regular replacement of AquaClear
filter inserts is essential for optimum filter
performance.
FILTER INSERTS MAINTENANCE
The AquaClear Foam, Carbon and Bio-max inserts should be changed alternately in order to maintain continuous biological
activity. Follow individual packaging instructions for recommended replacement intervals.
Never replace all Filter Inserts in any AquaClear Power Filter at the same time.
. PREPARING FILTER INSERTS
ALL FILTER INSERTS MUST BE RINSED THOROUGHLY PRIOR TO INSTALLATION.
a) Install intake “U” tube as shown and apply gentle
pressure to “click” into position.
b) Additional slight pressure is then applied to ensure
base of tube “clicks” into the opening over impeller
cover.
c) Attach extension tube on aquarium side of intake.
d) Add more than one extension tube if tank depth
requires it.
. ATTACHING
INTAKE “U” TUBE
After preparing filter inserts as indicated, place filter
basket into filter case. Gentle pressure may be necessary
to ease filter basket into position due to
the snug fitting foam insert.
. INSTALLING
FILTER INSERTS
®
a) Fill power filter case completely with water and
replace cover.
b) Adjust water flow control lever on intake “U” tube to
its maximum position for initial start-up.
c) Plug power cord into electrical outlet. Allow 30-45
seconds for priming (air to be expelled from “U” tube.)
d) After priming has been completed, move adjustment
control on intake “U” tube to adjust water flow rate
as required. (See How it Works— Patented
Refiltration System.)
IMPORTANT
DO NOT OPERATE FILTER WITHOUT WATER
NOTE: For maximum filter operation and efficiency,
regular cleaning of the filter and its parts is recommended
every two weeks. Soap or detergents are
NOT recommended for filter maintenance.
(See Power Filter Maintenance.)
. POWER FILTER
START-UP
Power filter must
be level to ensure
optimal performance.
Insert leveling device
into bottom of
filter case.
Mount power filter
onto rear of aquarium
and adjust leveling
device by turning to
required setting.
NOTE: If necessary,
an additional adjustment
may be made
to level power filter
by breaking off the
leveler bar at base of
motor.
. ATTACHING
LEVELING DEVICE
TROUBLE-SHOOTING & FAQs
Q. What if the power filter motor doesn’t start or makes a
mechanical noise?
A. Check to make sure impeller blades are free moving on magnet
assembly.
Q. Why won’t the power filter motor re-start after performing
filter insert maintenance?
A. Make sure unit has been plugged back into power outlet and that
all parts are thoroughly clean and replaced as directed.
(See Power Filter Maintenance..)
Q. What should I do if the priming process doesn’t occur?
A. Verifiy that:
• all parts are installed correctly
• filter case is completely filled with water
• unit is plugged into power outlet
• ensure “U” tube lever is set to maximum position
Q. Why is the water cloudy in my new aquarium?
A. Bacterial cloudiness may occur during the first week of a new
aquarium set-up and may last up to six weeks. If the condition
persists, consult your local aquarium professional.
Q. What happens if I forget to clean my filter inserts?
A. If the power filter is left unattended for too long, the filter inserts
become clogged with debris. In extreme cases, the filter basket
may be forced up from the filter case due to the pump pressure.
This is an indication that the efficiency of the filtration is very low
and that the filter inserts require immediate rinsing or replacement. (See Filter Inserts Maintenance.)
Q. When should I operate a reduced flow?
A. Reduced flow is most helpful during feeding times, or when the
input suction or output stream is too strong for small or delicate
fish. (See How it Works—Patented Refiltration System.)
Q. Why should I use only aquarium water to rinse my filter
inserts after they are installed?
A. Most cities add chlorine or other chemicals to eliminate harmful
bacteria in drinking water for human consumption. These additives, while harmless to us, are very toxic to fish.
ALSO AVAILABLE FROM AQUACLEAR®
Occasionally, it might be necessary to use alternate filter inserts to maintain a well balanced,
healthy aquatic environment. We offer the following alternative chemical stage inserts as superior solutions to your filtration system.
AquaClear Ammonia Remover Insert
· Removes and controls harmful ammonia
· Ideal for new or heavily populated aquariums
· Reduces stress on fish
· For freshwater use only
AquaClear Ammonia Remover Insert contains a natural ammonia removing
resin. This resin chemically bonds with ammonia to remove it from the
aquarium water. Use of the ammonia remover insert will reduce and control
toxic ammonia resulting in a healthy aquarium environment.
AquaClear Zeo-Carb Filter Insert
· Combines activated carbon and ammonia remover in one
· Removes toxic ammonia, odors, discoloration and impurities
· For use to prevent buildup of toxic ammonia
· Reduces stress on fish
· For freshwater use only
AquaClear Zeo-Carb Filter Insert contains a mixture of ammonia removing
resin and premium research grade carbon. This dual purpose insert gives
you the combined benefits of carbon and ammonia remover, while allowing
you additional space in your filter for other types of inserts.
NUTRAFIN® WATER CARE PRODUCTS
For Improved Aquarium Health
AquaPlus®: Patented stress relief water conditioner. Makes tap water safe.
Protects fish and helps heal damaged fins, cuts, and wounds. Ideal for new
tank set-up and water changes.
Cycle®: Biological aquarium supplement
Introduces beneficial bacteria to accelerate
the maturation of new tanks. Promotes
tank health and reduces fish loss when
used as part of weekly maintenance.
REPLACEMENT PARTS
To re-order parts for your AquaClear Power Filter please refer to Parts List below..
NEW MODEL # 20 30 50 70 110
Formerly model Mini 150 200 300 500
Article # A595 A600 A610 A615 A620
A Filter Case A16020 A16120 A16220 A16320 A16420
B Filter Basket A16040 A16140 A16240 A16340 A16440
C Filter Cover A16030 A16130 A16230 A16330 A16430
D Intake "U" Tube A16050 A16150 A16150 A16350 A16350
E Extension Tube A625 A625 A625 A627 A627
F Impeller Cover A16015 A16015 A16015 A16315 A16415
G Impeller Assembly A630 A632 A634 A636 A638
H Seal Ring A16017 A16017 A16017 A16017 A16417
I Motor Unit A16000 A16000 A16000 A16000 A16400
J Leveling Device A16325 A16325 A16325 A16325 A16325
* Intake "U" Tube Adaptor N/A N/A N/A N/A A16412
®
A
B
C
F
G
HI
J
*Not shown. Available for Model 110 only.
HOW TO CONTACT US
If you have a problem, or have questions about the operation of this product, please let us try to
help you before returning product to your dealer. Most problems can be handled promptly with a
toll-free phone call. Or if you prefer, you can contact us on our web site at www.hagen.com.
When you call (or write), please have all relevant information, such as model number and/or
part numbers available, as well as the nature of the problem.
CALL US ON OUR TOLL FREE NUMBER 1-800-724-2436 between 8:30 am and 4:00 p.m.
Eastern Standard Time. Ask for Customer Service.
FOR AUTHORIZED GUARANTEE CONSUMER SERVICE: Return unit with dated receipt
plus $5.00 for shipping and handling to:
Rolf C. Hagen (U.S.A.) Corp.
Consumer Repair
50 Hampden Road
Mansfield, MA 02048
LIFETIME GUARANTEE
AquaClear Power Filters are guaranteed against defects in material or workmanship under normal aquarium usage and service for as long as you own
the filter. We offer a Lifetime Guarantee on all non-replaceable parts which
means that the filter will be repaired or replaced at the manufacturer’s discretion, free of charge, when the complete pump is returned with proof of purchase and postage paid. Please include $5.00 to cover shipping and handling. This warranty does not apply to any filter that has been subjected to
misuse, negligence, or tampering. No liability is assumed with respect to loss
or damage to livestock or personal property irrespective of the cause thereof.
REGISTER ON-LINE: www.hagen.com.
· To learn more about Hagen products.
· For a copy of our FREE full color, 40 page, Basic Aquarium Guide.
© 2003 Rolf C. Hagen (USA) Corp. All Rights Reserved. HAGEN, CYCLEGUARD, NUTRAFIN,
AQUAPLUS, and CYCLE are registered trademarks of Rolf C. Hagen (USA) Corp., Mansfield, MA.
D
E
30, 50, 70
and 110
Instruction Manual
See inside for Quick Start Guide!
English
IMPORTANT SAFEGUARDS
WARNING–To guard against injury, basic safety precautions should be
observed, including the following:
1. For the complete enjoyment, use and understanding of this product,
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
and all-important notices on the AquaClear Power Filter before
using. Failure to do so may result in damage to the unit.
2. DANGER—To avoid possible electrical shock, special care should
be taken since water is employed in the use of this equipment. For
each of the following situations, do not attempt repairs yourself;
return the AquaClear Power Filter to an authorized service facility for
service or discard the appliance.
I. If the AquaClear Motor Unit falls into the water DO NOT reach
for it! First unplug it and then retrieve it. If any of the electrical
components of the AquaClear Power Filter gets wet, unplug
it immediately.
II. If the AquaClear Motor Unit shows any sign of abnormal water
leakage or if RCD (or GFCI- Ground Fault Current Interrupter)
switches off disconnect the power supply cord from mains and
remove pump from water.
III. Carefully examine the AquaClear Power Filter after installation. It
should not be plugged in if there is water on parts not intended to
be wet.
IV. Do not operate any appliance if it has a damaged cord or plug, or
if it is malfunctioning or if it is dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the
cord is damaged, the appliance should be discarded. Never cut
the cord.
V. To avoid the possibility of the AquaClear Power
Filter’s plug or receptacle getting wet, position the
unit to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug.
A “drip loop” (A) should be arranged to the receptacle. The “drip loop” is the part of the cord below the
level of the receptacle or the connector if an extension cord is used, to prevent water traveling along
the cord and coming into contact with the receptacle.
If the plug or receptacle does get wet, DO NOT
unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug
and examine for presence of water in the receptacle. A
3. Close supervision is necessary when any appliance is used by or
near children.
4. To avoid injury, do not contact moving parts or hot parts such
as heaters, reflectors, lamp bulbs, etc.
5. CAUTION— Always unplug or disconnect all appliances in the
aquarium from electricity supply before placing hands in water,
before putting on or taking off parts and whilst the equipment is
being installed, maintained or handled. When inserting or removing
the pump from the water, always pull out the main electricity plug.
Never yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect. Always unplug an appliance from an outlet when not
in use.
6. Do not use this pump for other than intended use (i.e.: do not use
in swimming pools, bathrooms, etc.). The use of attachments not
recommended or sold by the appliance manufacturer may cause an
unsafe condition.
· Do not use this pump in swimming pools or other situations where
people are immersed.
· This pump is suitable for use in water temperatures up to 35 °C.
· Do not use this pump with inflammable or drinkable liquids.
7. This pump is suitable for INDOOR use only. Do not install or store
the appliance where it will be exposed to the weather or to
temperatures below freezing.
8. Make sure an appliance mounted on a tank is securely installed
before operating it.
9. Read and observe all the important notices on the appliance.
10. If an extension cord is necessary, a cord with a proper rating
should be used. A cord rated for less amperes or watts than the
appliance rating may overheat. Care should be taken to arrange
the cord so that it will not be tripped over or pulled.The connection
should be carried out by a qualified electrical installer.
11. The pump must not run dry.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this power filter it is recommended that this manual is thoroughly read and understood.
Failure to do so may result in damage to this filter.
AQUACLEAR POWER FILTERS FLOW RATES
MODEL # 20 30 50 70 110
Maximum Flo Rate 100 gph 150 gph 200 gph 300 gph 500 gph
378 lph 568 lph 757 lph 1135 lph 1890 lph
Minimum Flo Rate 33 gph 50 gph 66.6 gph 100 gph 166.6 gph
125 lph 190 lph 250 lph 380 lph 630 lph
Watts 6 Watts 6 Watts 6 Watts 6 Watts 14 Watts
RPM 3600 rpm 3600 rpm 3600 rpm 3600 rpm 3600 rpm
POWER FILTER MAINTENANCE
Always unplug power filter prior to cleaning. Remove cover, filter basket, and discard water
remaining in the filter case. Thoroughly rinse collected debris from the case, impeller cover and
impeller assembly in clear lukewarm water. The intake “U” tube and extension tube can be
cleaned with a filter stem brush to remove any buildup of deposits. When all parts have been
cleaned and thoroughly rinsed, reassemble filter and replace onto aquarium.
(See Quick Start Guide 2, 3 and 4.)
Follow operating instructions to restart and prime power filter.
(See Power Filter Start-up.)
Every three months the
motor should be thoroughly
cleaned. Remove
cover, filter basket and
discard water remaining
in filter case. Remove
motor by twisting a 1/4
–turn gently in the direction
of the arrow on front.
Ease motor down slowly
to prevent damage to the
filter and motor guide.
Pull impeller out of
impeller well and rinse to
remove accumulated
slime deposits.
A cotton swab or
impeller well brush (not
supplied) can be used to
remove more stubborn
deposits. Wet motor seal
ring to prevent damage
before placing into filter
case.
HOW IT WORKS
The AquaClear Power Filter draws water from the aquarium
through an extension tube into the motor which then pumps water
out of the impeller assembly. The intake “U” tube directs the flow of
unfiltered water through filter inserts to trap particles, debris, and
purify the water.
CYCLEGUARD® MULTI-STAGE
FILTRATION SYSTEM
Provides optimal Mechanical, Chemical,
and Biological filtration
A healthy aquarium requires “beneficial” bacteria.
Invisible and harmless, beneficial bacteria are essential in the removal of
toxic ammonia and nitrite.
With cartridge filtration systems, when you throw away the cartridge, you throw away beneficial
bacteria. It can take weeks for the bacteria to recolonize, resulting in a stressful environment.
The AquaClear® multi-stage filtration system is different. Only one of three filtration components
is changed at a time. This ensures that significant amounts of beneficial bacteria remain. There
is never a sudden depletion of bacteria so biological filtration remains at highly effective levels.
Stage 1: Mechanical—Foam Filter Insert
AquaClear Foam Filter Inserts perform mechanical filtration by trapping particles and debris as
they pass through the insert. This unique foam, designed for use with AquaClear Power Filters,
features optimal pore size for efficient mechanical and biological filtration.
Stage 2: Chemical—Activated Carbon insert
AquaClear Activated Carbon Filter Insert contains 100% premium
research grade carbon. Premium research grade carbon provides
large amounts of surface area for adsorption of undesirable
impurities. The activated carbon filter insert will remove unwanted
odors, discoloration and impurities resulting in a crystal clear
aquarium.
Stage 3: Biological—BioMax Insert
AquaClear BioMax Filter Insert contains BioMax ceramic rings.
The surface of BioMax is made up of a complex pore system that
allows bacteria to thrive. Each ceramic ring contains approximately
100 square feet of surface area providing more biological power
than a traditional cartridge. Use of the BioMax Insert will provide optimal living space for beneficial
bacteria and enhance the removal of ammonia and nitrites resulting in a healthy aquarium
environment.
NOTE: Regular replacement of AquaClear filter inserts is essential for optimum
filter performance.
PATENTED REFILTRATION SYSTEM
For a healthy aquarium and clear water
Sometimes delicate fish and plants require a gentler water flow. AquaClear’s patented refiltration
system allows you to control the flow rate without compromising filtration efficiency.
When the flow rate is reduced, up to 50% of the water within the filter chamber is processed
multiple times. More impurities are filtered out, creating a healthier tank with sparkling clean
and clear water.
NOTE: A reduced flow rate is also recommended for use during feeding, to ensure more
efficient food consumption and less waste.
STAGE 1
STAGE 2
STAGE 3
®
Congratulations on the purchase of your new AquaClear
Power Filter. Please allow approximately 15-20 minutes
for the complete installation of filter parts and inserts.
The rewards to your aquatic adventures will be worth it!
Inspect AquaClear power filter for any visible signs of
shipping damage and verify that motor is securely fastened
to filter case. The following parts should be included
in your package.
*All AquaClear Power Filters, except Model 20, are shipped with two
extension tubes.
AquaClear® Power Filter Quick Start Guide
Filter
Case
Filter
Basket
Filter Cover
Intake
“U” Tube
Extension
Tube*
Motor
Leveling
Device
Foam
Carbon
Locking Clip
BioMax
Mesh Bag
. PACKING LIST
AquaClear Foam: Rinse foam insert and place into filter basket first. The foam block should
totally fill the bottom of the basket leaving no space between the filter basket base and sides.
Replace foam insert every two months.
AquaClear Carbon: Remove carbon insert from dust sleeve and rinse pouch to remove any
carbon dust particles. Flatten carbon insert and place horizontally on top of foam insert.
Replace carbon insert every month.
AquaClear BioMax: Open poly bag and transfer
contents into mesh bag. Apply locking clip
as shown, trim excess mesh, and thoroughly
rinse insert materials before placing on third
level of the basket.
Replace BioMax insert every three months.
NOTE: Regular replacement of AquaClear
filter inserts is essential for optimum filter
performance.
FILTER INSERTS MAINTENANCE
The AquaClear Foam, Carbon and Bio-max inserts should be changed alternately in order to maintain continuous biological
activity. Follow individual packaging instructions for recommended replacement intervals.
Never replace all Filter Inserts in any AquaClear Power Filter at the same time.
. PREPARING FILTER INSERTS
ALL FILTER INSERTS MUST BE RINSED THOROUGHLY PRIOR TO INSTALLATION.
a) Install intake “U” tube as shown and apply gentle
pressure to “click” into position.
b) Additional slight pressure is then applied to ensure
base of tube “clicks” into the opening over impeller
cover.
c) Attach extension tube on aquarium side of intake.
d) Add more than one extension tube if tank depth
requires it.
. ATTACHING
INTAKE “U” TUBE
After preparing filter inserts as indicated, place filter
basket into filter case. Gentle pressure may be necessary
to ease filter basket into position due to
the snug fitting foam insert.
. INSTALLING
FILTER INSERTS
®
a) Fill power filter case completely with water and
replace cover.
b) Adjust water flow control lever on intake “U” tube to
its maximum position for initial start-up.
c) Plug power cord into electrical outlet. Allow 30-45
seconds for priming (air to be expelled from “U” tube.)
d) After priming has been completed, move adjustment
control on intake “U” tube to adjust water flow rate
as required. (See How it Works— Patented
Refiltration System.)
IMPORTANT
DO NOT OPERATE FILTER WITHOUT WATER
NOTE: For maximum filter operation and efficiency,
regular cleaning of the filter and its parts is recommended
every two weeks. Soap or detergents are
NOT recommended for filter maintenance.
(See Power Filter Maintenance.)
. POWER FILTER
START-UP
Power filter must
be level to ensure
optimal performance.
Insert leveling device
into bottom of
filter case.
Mount power filter
onto rear of aquarium
and adjust leveling
device by turning to
required setting.
NOTE: If necessary,
an additional adjustment
may be made
to level power filter
by breaking off the
leveler bar at base of
motor.
. ATTACHING
LEVELING DEVICE
TROUBLE-SHOOTING & FAQs
Q. What if the power filter motor doesn’t start or makes a
mechanical noise?
A. Check to make sure impeller blades are free moving on magnet
assembly.
Q. Why won’t the power filter motor re-start after performing
filter insert maintenance?
A. Make sure unit has been plugged back into power outlet and that
all parts are thoroughly clean and replaced as directed.
(See Power Filter Maintenance..)
Q. What should I do if the priming process doesn’t occur?
A. Verifiy that:
• all parts are installed correctly
• filter case is completely filled with water
• unit is plugged into power outlet
• ensure “U” tube lever is set to maximum position
Q. Why is the water cloudy in my new aquarium?
A. Bacterial cloudiness may occur during the first week of a new
aquarium set-up and may last up to six weeks. If the condition
persists, consult your local aquarium professional.
Q. What happens if I forget to clean my filter inserts?
A. If the power filter is left unattended for too long, the filter inserts
become clogged with debris. In extreme cases, the filter basket
may be forced up from the filter case due to the pump pressure.
This is an indication that the efficiency of the filtration is very low
and that the filter inserts require immediate rinsing or replacement. (See Filter Inserts Maintenance.)
Q. When should I operate a reduced flow?
A. Reduced flow is most helpful during feeding times, or when the
input suction or output stream is too strong for small or delicate
fish. (See How it Works—Patented Refiltration System.)
Q. Why should I use only aquarium water to rinse my filter
inserts after they are installed?
A. Most cities add chlorine or other chemicals to eliminate harmful
bacteria in drinking water for human consumption. These additives, while harmless to us, are very toxic to fish.
ALSO AVAILABLE FROM AQUACLEAR®
Occasionally, it might be necessary to use alternate filter inserts to maintain a well balanced,
healthy aquatic environment. We offer the following alternative chemical stage inserts as superior solutions to your filtration system.
AquaClear Ammonia Remover Insert
· Removes and controls harmful ammonia
· Ideal for new or heavily populated aquariums
· Reduces stress on fish
· For freshwater use only
AquaClear Ammonia Remover Insert contains a natural ammonia removing
resin. This resin chemically bonds with ammonia to remove it from the
aquarium water. Use of the ammonia remover insert will reduce and control
toxic ammonia resulting in a healthy aquarium environment.
AquaClear Zeo-Carb Filter Insert
· Combines activated carbon and ammonia remover in one
· Removes toxic ammonia, odors, discoloration and impurities
· For use to prevent buildup of toxic ammonia
· Reduces stress on fish
· For freshwater use only
AquaClear Zeo-Carb Filter Insert contains a mixture of ammonia removing
resin and premium research grade carbon. This dual purpose insert gives
you the combined benefits of carbon and ammonia remover, while allowing
you additional space in your filter for other types of inserts.
NUTRAFIN® WATER CARE PRODUCTS
For Improved Aquarium Health
AquaPlus®: Patented stress relief water conditioner. Makes tap water safe.
Protects fish and helps heal damaged fins, cuts, and wounds. Ideal for new
tank set-up and water changes.
Cycle®: Biological aquarium supplement
Introduces beneficial bacteria to accelerate
the maturation of new tanks. Promotes
tank health and reduces fish loss when
used as part of weekly maintenance.
REPLACEMENT PARTS
To re-order parts for your AquaClear Power Filter please refer to Parts List below..
NEW MODEL # 20 30 50 70 110
Formerly model Mini 150 200 300 500
Article # A595 A600 A610 A615 A620
A Filter Case A16020 A16120 A16220 A16320 A16420
B Filter Basket A16040 A16140 A16240 A16340 A16440
C Filter Cover A16030 A16130 A16230 A16330 A16430
D Intake "U" Tube A16050 A16150 A16150 A16350 A16350
E Extension Tube A625 A625 A625 A627 A627
F Impeller Cover A16015 A16015 A16015 A16315 A16415
G Impeller Assembly A630 A632 A634 A636 A638
H Seal Ring A16017 A16017 A16017 A16017 A16417
I Motor Unit A16000 A16000 A16000 A16000 A16400
J Leveling Device A16325 A16325 A16325 A16325 A16325
* Intake "U" Tube Adaptor N/A N/A N/A N/A A16412
®
A
B
C
F
G
HI
J
*Not shown. Available for Model 110 only.
HOW TO CONTACT US
If you have a problem, or have questions about the operation of this product, please let us try to
help you before returning product to your dealer. Most problems can be handled promptly with a
toll-free phone call. Or if you prefer, you can contact us on our web site at www.hagen.com.
When you call (or write), please have all relevant information, such as model number and/or
part numbers available, as well as the nature of the problem.
CALL US ON OUR TOLL FREE NUMBER 1-800-724-2436 between 8:30 am and 4:00 p.m.
Eastern Standard Time. Ask for Customer Service.
FOR AUTHORIZED GUARANTEE CONSUMER SERVICE: Return unit with dated receipt
plus $5.00 for shipping and handling to:
Rolf C. Hagen (U.S.A.) Corp.
Consumer Repair
50 Hampden Road
Mansfield, MA 02048
LIFETIME GUARANTEE
AquaClear Power Filters are guaranteed against defects in material or workmanship under normal aquarium usage and service for as long as you own
the filter. We offer a Lifetime Guarantee on all non-replaceable parts which
means that the filter will be repaired or replaced at the manufacturer’s discretion, free of charge, when the complete pump is returned with proof of purchase and postage paid. Please include $5.00 to cover shipping and handling. This warranty does not apply to any filter that has been subjected to
misuse, negligence, or tampering. No liability is assumed with respect to loss
or damage to livestock or personal property irrespective of the cause thereof.
REGISTER ON-LINE: www.hagen.com.
· To learn more about Hagen products.
· For a copy of our FREE full color, 40 page, Basic Aquarium Guide.
© 2003 Rolf C. Hagen (USA) Corp. All Rights Reserved. HAGEN, CYCLEGUARD, NUTRAFIN,
AQUAPLUS, and CYCLE are registered trademarks of Rolf C. Hagen (USA) Corp., Mansfield, MA.
D
E